MotorCodex Español

P0776 — Pressure Control Solenoid B Performance / Stuck Off

Moderate

Quick answer

P0776 means the computer commanded pressure control solenoid B to set a specific hydraulic pressure and the transmission didn’t deliver it — the solenoid is stuck, sluggish, or the pressure is leaking away downstream. Check fluid level and condition first: contaminated fluid is the classic cause. Symptoms range from harsh shifts to slipping and limp mode.

What it means

Pressure control solenoids are the transmission’s pressure faucets: the computer pulses them to set exactly how firmly each clutch applies (and, for the main solenoid, the line pressure feeding everything else). P0776 is a results code — solenoid B was commanded, and the pressure feedback or the resulting gear behavior says the hydraulics didn’t follow orders.

Which clutch circuit solenoid B feeds varies by transmission — on many six-speed automatics it controls one of the midrange clutches, so the complaint clusters around the same specific shifts (a flare or a bang on the same gear change every time) rather than everything at once.

“Performance / stuck off” is hydraulic language, not electrical. The wiring tested fine — an open or short would set a different code — what failed is the result. That’s why fluid condition dominates this diagnosis: varnish and clutch debris make these precision valves stick, and a fluid service genuinely cures a share of them.

P0776 symptoms: what you'll notice

  • Harsh, banging shifts — stuck pressure regulation often defaults to maximum line pressure as self-protection.
  • Slipping or RPM flare between gears when the commanded pressure never arrives at the clutch.
  • Limp mode: held in one gear, sluggish takeoff, check engine light on.
  • Shudder or delayed engagement, often worse once the fluid is fully warm.

Common causes

Ordered from most to least likely.

  1. 1.

    Low or contaminated transmission fluid

    Always first. Debris and varnish stick the solenoid’s precision valve, and a low level starves the pump that feeds it.

  2. 2.

    Sticking or worn pressure control solenoid

    These are fine-tolerance spool valves that live in hot, dirty fluid — they wear out, and they stick long before they die electrically.

  3. 3.

    Valve body wear

    A worn bore bleeds off the pressure the solenoid sets — the solenoid gets blamed for the bore’s sins. Common at high mileage.

  4. 4.

    Clutch seal or sealing-ring leak downstream

    The commanded pressure escapes at the clutch itself; often arrives with a ratio code for one specific gear.

  5. 5.

    Internal pump wear

    The expensive theory — earn it by ruling out fluid, solenoid, and wiring first.

How to fix it: diagnosis, step by step

Cheapest and most likely checks first.

  1. 1 Check the fluid first

    Level per your vehicle’s procedure, color on a white towel, smell. Dirty or burnt fluid is both the most likely cause and the cheapest fix — and it changes how you read every other test.

  2. 2 Read the code pattern

    One pressure solenoid code points at that circuit; several at once point at shared causes (fluid, pump, line pressure). Note whether a gear-ratio code accompanies P0776 — that names the clutch that isn’t getting its pressure.

  3. 3 Service the fluid and filter, clear, re-test

    On a sticking solenoid this is diagnosis and cure in one step. If the code stays away, you’re done; if it returns quickly, the solenoid or valve body needs real attention.

  4. 4 Test or replace the solenoid

    Access varies enormously: on some transmissions pressure solenoids sit on the valve body reachable from the pan, on others (and most CVTs) the valve body has to come out. Get the labor picture for your unit before deciding DIY vs. shop.

  5. 5 Line pressure test if it persists

    A gauge on the line-pressure tap separates “solenoid not commanding” from “pump/valve body not delivering” — the fork in the road between a small repair and a big one.

Parts & tools you may need

Disclosure: some links are affiliate links (including the Amazon Associates program). If you buy through them, we may earn a commission at no extra cost to you.

Related codes

Frequently asked questions

What does code P0776 mean?
P0776 means the computer commanded pressure control solenoid B to set a specific hydraulic pressure and the transmission didn’t deliver it — the solenoid is stuck, sluggish, or the pressure is leaking away downstream. It’s moderately serious — you can usually keep driving gently, but diagnose it soon.
What does “stuck off” actually mean — is P0776 an electrical problem?
No — that’s the key distinction. The computer can talk to the solenoid fine (a wiring fault would set a different code); it’s the hydraulic result that’s missing. The valve is stuck, lazy, or the pressure it sets is leaking away. Diagnosis is about fluid and hydraulics, not the connector.
Can I drive with P0776?
If shifting still feels normal, short-term gentle driving is usually tolerable. If it’s slipping, flaring, or in limp mode, park it and diagnose — slip eats clutch material, and the repair bill grows with every slip.
How much does it cost to fix P0776?
A fluid and filter service runs $80–250 and cures the sticky-valve cases. The solenoid itself is often a $30–120 part, but labor swings from under an hour (pan-accessible) to several hours (valve body out) — $150–700 installed is the honest range. Valve body or pump work costs more; confirm the diagnosis first.
Is my transmission dead?
Usually not. Most of these codes resolve at the fluid, solenoid, or valve-body level — repairs in the hundreds. A rebuild only enters the conversation when slipping persists after those layers check out, which is the minority of cases.
Ask Codi