MotorCodex Español

P0715 — Input/Turbine Speed Sensor Circuit

Moderate

Quick answer

P0715 means the sensor measuring how fast the transmission’s input shaft spins isn’t producing a valid signal — and without it the computer can’t verify gear ratios. Typical symptoms: harsh or erratic shifting, no speedometer issues (that’s the output sensor), often paired with ratio codes. Before anything else: inspect the sensor’s connector and measure its resistance; check for metal debris on the magnetic tip.

What it means

Automatic transmissions are controlled hydraulically but supervised electronically: sensors report shaft speeds, temperature, and gear position, and solenoids convert the computer’s decisions into fluid pressure. P0715 reports that the sensor measuring how fast the transmission’s input shaft spins isn’t producing a valid signal — and without it the computer can’t verify gear ratios.

The golden rule of transmission codes: check the fluid before believing any other theory. Level, color (should be red/pink, not brown), and smell (burnt = bad news) — degraded fluid causes shifting complaints, solenoid misbehavior, and ratio errors that perfectly imitate failed parts.

P0700 usually accompanies this code; it’s just the pointer that tells the engine computer to turn on the light. Diagnose the specific code, not P0700.

Common causes

Ordered from most to least likely.

  1. 1.

    Low, degraded, or wrong-spec transmission fluid

    Always first. The fluid specification matters as much as the level.

  2. 2.

    Failed sensor or solenoid (per the specific code)

    Most test with a simple resistance measurement at the case connector.

  3. 3.

    Wiring or connector damage at the transmission

    The case connector lives in heat and spray; corroded pins are common.

  4. 4.

    Internal wear (clutches, valve body)

    The expensive story — earn it by ruling out the cheap ones first.

How to diagnose it, step by step

Cheapest and most likely checks first.

  1. 1 Check the fluid first

    Level per your vehicle’s procedure (dipstick or level-check plug), color on a white towel, and smell. Burnt or brown fluid reframes the whole diagnosis; low fluid plus a leak explains half of these codes.

  2. 2 Read all transmission codes

    Use a scanner that addresses the transmission module. The combination of codes (one solenoid vs. several, sensor + ratio together) localizes the fault.

  3. 3 Inspect the sensor’s connector and measure its resistance; check for metal debris on the magnetic tip

    This is the code-specific first move — do it before parts shopping.

  4. 4 Test electrically at the case connector

    Most transmission sensors and solenoids can be resistance-tested from the external connector with a wiring diagram, no disassembly needed.

  5. 5 Decide: pan-level repair or specialist

    Fluid, external sensors, and many solenoids are DIY-reachable. Valve body and internal clutch work usually isn’t — and a specific, confirmed code is exactly what an honest transmission shop wants to see.

Parts & tools you may need

  • OBD-II scanner with transmission module coverage
  • Digital multimeter
  • Correct transmission fluid for your vehicle (specification matters enormously)
  • Transmission pan gasket/filter kit (if dropping the pan)
  • Replacement sensor or solenoid (only after electrical tests confirm)

Disclosure: some links are affiliate links. If you buy through them, we may earn a commission at no extra cost to you.

Related codes

Frequently asked questions

Can I drive with P0715?
Usually yes for the short term, especially if shifting feels normal. If the transmission enters limp mode or starts slipping, stop driving it and diagnose — slip damage compounds fast.
Will a fluid change fix it?
If the fluid is low, burnt, or wrong-spec — quite possibly, and it’s the mandatory first step regardless. It won’t fix a genuinely failed solenoid or sensor, which is why you test those electrically before and after.
Is this code a “transmission rebuild”?
Usually not. Most codes in this family are sensors, solenoids, wiring, or fluid — hundreds, not thousands. Internal repair only enters the picture when ratio/slip codes persist after the electrical and fluid layers check out.
Why do I also have P0700?
P0700 is just the messenger: the transmission module asked the engine computer to turn on the light. Your real diagnosis is this code.