MotorCodex Español

P0333 — Knock Sensor (Sensor 2 / Bank 2) — Circuit High Input

Moderate

Quick answer

P0333 means the knock sensor 2’s the signal is stuck high — typically a short to voltage, a broken ground or reference wire, or a failed sensor. Same story as sensor 1: the computer retards timing defensively, costing power and economy, while real knock on that bank goes unguarded. Check the connector and wiring before buying a sensor — for this variant of the code, wiring is the most common answer.

What it means

The knock sensor (sensor 2 / bank 2) tells the engine computer detonation on the second bank of a V engine (or a second location on long engines), protecting that side from knock damage. P0333 sets when the signal is stuck high — typically a short to voltage, a broken ground or reference wire, or a failed sensor for long enough that the computer stops trusting it.

Circuit codes describe electrical behavior, which puts the wiring, the connector, and the sensor on equal footing as suspects. The cheapest of the three fails most often.

While the signal is untrusted, the computer substitutes a safe default value. The engine runs, but on assumptions instead of measurements — that’s the drivability change you feel.

Common causes

Ordered from most to least likely.

  1. 1.

    Wiring damage (chafe, break, melted insulation)

    A short to voltage or broken ground pins the signal high.

  2. 2.

    Corroded, loose, or backed-out connector pins

    Unplug and inspect both halves under good light.

  3. 3.

    Failed knock sensor 2

    Confirm with measurements before replacing.

  4. 4.

    Harness damage under the intake manifold

    Frequently traced to a previous repair that disturbed the valley harness.

  5. 5.

    Lost 5V reference or sensor ground (where applicable)

    If several sensors fault together, suspect a shared reference circuit rather than coincidence.

How to diagnose it, step by step

Cheapest and most likely checks first.

  1. 1 Read the freeze frame

    Note when P0333 sets — cold start, warm idle, under load, over bumps. The conditions narrow the cause dramatically, especially for intermittent faults.

  2. 2 Inspect connector and harness

    Unplug the sensor; check for corrosion, bent or spread pins, and chafed insulation along the harness run. Re-seat firmly. This free step resolves a remarkable share of circuit codes.

  3. 3 Watch it in live data

    Test by response: with a capable scanner watching knock activity, a light tap on the block near sensor 2 should register. Compare behavior against sensor 1.

  4. 4 Check torque, condition, and the harness run

    On many V engines these sensors live under the intake manifold — wiring damaged during unrelated intake work is a classic cause. Reinstall to exact torque spec.

  5. 5 Wiggle-test if intermittent

    Engine running, data live: gently flex the harness and tap the sensor while watching the reading. A glitch you can provoke is a fault you can find.

  6. 6 Replace with a quality part

    If measurements condemn the sensor, buy OEM or a reputable brand — bargain sensors re-set these codes often enough to cost more in time than they save in money.

Parts & tools you may need

  • OBD-II scanner (code reader with freeze frame / live data)
  • Digital multimeter
  • Electrical contact cleaner
  • Replacement knock sensor 2 (exact part for your engine)

Disclosure: some links are affiliate links. If you buy through them, we may earn a commission at no extra cost to you.

Related codes

Frequently asked questions

Can I drive with P0333?
Yes, gently, on good fuel — same conservative-timing caveats as any knock sensor fault.
Is it the sensor or the wiring?
For this variant, lean wiring: stuck-low, stuck-high, and intermittent signatures are circuit behaviors. Inspect and measure before buying the sensor.
Why did the code return after a new sensor?
Because the circuit, not the sensor, was the fault — or the replacement was low quality. Re-do the wiring inspection the first repair skipped.
What does the computer do meanwhile?
It substitutes a default value and keeps the engine running on assumptions. Functional, but you pay in drivability and fuel until the real measurement comes back.