MotorCodex Español

P0023 — Camshaft Position Actuator "B" Circuit (Bank 2)

Moderate

Quick answer

P0023 means an electrical fault in the oil control solenoid that adjusts the "B" camshaft (exhaust on most engines) on bank 2. Before anything else, check the oil: VVT systems are hydraulic, and low, dirty, or wrong-viscosity oil is the leading cause of the entire code family. The oil control solenoid is the usual part-level fix.

What it means

Variable valve timing (VVT/VTC/VANOS — every maker brands it differently) rotates the camshaft slightly relative to the crankshaft while the engine runs, trading idle smoothness, midrange torque, and top-end power as conditions change. The computer does this hydraulically: an oil control solenoid meters pressurized engine oil into a phaser on the cam gear. P0023 reports that an electrical fault in the oil control solenoid that adjusts the "B" camshaft (exhaust on most engines) on bank 2.

Circuit codes are electrical: the solenoid winding, its connector, or the wiring — measured with a multimeter, not guessed at. The solenoid is cheap and accessible on most engines, which makes this one of the friendlier codes in the family.

Because everything here floats on oil pressure, oil neglect is the family's root villain: sludge clogs the solenoid's screen, low level starves the phaser, and the wrong viscosity changes how fast the system responds.

Common causes

Ordered from most to least likely.

  1. 1.

    Low oil level, degraded oil, or wrong viscosity

    The #1 cause across the family — check before touching tools.

  2. 2.

    Oil control solenoid stuck or its filter screen clogged

    Removable and inspectable on most engines; debris on the screen is a confession.

  3. 3.

    Solenoid winding open or shorted

    Measure resistance against spec at the connector.

  4. 4.

    Wiring or connector damage

    Oil-soaked connectors are common here — leaking valve covers drip onto them.

  5. 5.

    Sludged oil passages

    Engines with neglected oil-change histories — the system's arteries are narrow.

How to diagnose it, step by step

Cheapest and most likely checks first.

  1. 1 Check the oil first

    Level on the dipstick, condition on a white towel, and viscosity against the cap/manual. If the oil is low, black, or wrong, change it (correct spec) and clear the code — a meaningful share of VVT codes end right here.

  2. 2 Inspect and test the oil control solenoid

    Unplug it: measure winding resistance against spec (typically single-digit ohms). Check the connector for oil intrusion and bent pins. If electrical tests pass, remove it and inspect the screen for debris.

  3. 3 Watch commanded vs. actual cam position

    On a scanner with VVT data, command timing changes (or watch during a test drive): actual position should track commanded smoothly. Lazy tracking = hydraulics (oil, solenoid, phaser); no movement at all on a good circuit = phaser.

  4. 4 Listen for the mechanical tells

    Cold-start rattle that fades = phaser wear. Constant chain noise or a correlation code (P0019) alongside = the timing chain conversation, which is a bigger job and worth confirming with cam/crank correlation data before opening anything.

  5. 5 Re-evaluate after the cheap fixes

    Fresh correct oil + cleaned/new solenoid resolves most of this family. If codes persist, the phaser or chain is next — engine-specific work where a vehicle-specific guide or shop makes sense.

Parts & tools you may need

  • OBD-II scanner (code reader with freeze frame / live data)
  • Digital multimeter
  • Oil control (VVT) solenoid for your engine
  • Oil change supplies — correct viscosity and a quality filter

Disclosure: some links are affiliate links. If you buy through them, we may earn a commission at no extra cost to you.

Related codes

Frequently asked questions

Can I drive with P0023?
Generally yes, short-term: expect reduced power or economy and possibly rough idle while the computer parks the cam in a safe default position. If it's accompanied by loud rattling or a correlation code, treat it more urgently — timing hardware problems don't improve with miles.
Why does an oil change fix a timing code?
Because VVT is a hydraulic system that uses engine oil as its working fluid. Low level starves it, sludge clogs its screens and passages, and wrong viscosity changes its response. The code describes timing; the mechanism is oil.
Is this the timing chain?
Sometimes. A stretched chain shifts the cam's baseline and the VVT system runs out of authority correcting it. The tell is a correlation code (P0019) alongside, cold-start rattle that doesn't fade, or correlation drift in live data. Solenoid-level causes are far more common — rule them out first.
The code came back after I replaced the solenoid. Now what?
Verify the oil (again — it really is the usual suspect), check the connector and wiring you reused, and then look deeper: phaser wear or chain stretch. A compression test and cam/crank correlation reading guide the next step.